Ledford Gage Lab, Inc.

Sales and Calibration of Test and Measurement Equipment!

The Ledford Gage Lab

Measuring

Ledford's state-of-the-art facility was designed with dimensional calibration in mind. Opened in 1998, the laboratory has double wall construction with a four inch air envelope allowing optimum environmental control. Temperature and humidity are controlled by a CSI computer system which samples every thirty seconds and adjusts every three minutes as needed. A 25 inch slab floor, R-60 insulation and a .0101 micron filter system ensure the conditions necessary for measurements in the millionths.

Measureing

The lab is equipped with state-of-the-art computerized technical precision equipment including coordinate measuring machines, a laser interferometer system and micro-process or digital height gages. This equipment speeds service and assures precise measurement accuracy.

Capabilities

  • Expedite (1-Day 50% Added)
  • Expedite (2-Day 35% Added)
  • Expedite (3-Day 25% Added)
  • Minimum Charge - Lab Orders $25.00

Gage Blocks & Standards

  • Angle Gage Blocks
  • Gage Blocks - Steel to 4"
  • Gage Blocks - 5 to 20"
       minimum 17.50 + .50 per inch
  • Gage Blocks Carbide to 4"
  • Accessory Set
  • Accessory
  • Gage Blocks - Ceramic to 4"
  • Gage Blocks - Grade 1
  • Gage Blocks - Ceramic Grade 1
  • Length Standards to 6"
  • Length Standards 7 - 30" (per inch)
  • Length Standards 31 - 54" (per inch)
  • Length Standards 55 - 120" (per inch)
  • Micrometer Master (per Reading)
  • Caliper Master (per Reading)
  • Depth Micrometer Master (per Reading)
  • Standard Reference Bar to 12"
  • Standard Reference Bar 13 - 19"
  • Standard Reference Bar 20 - 25"
  • Standard Reference Bar 26 - 37"
  • Optical Flats 0 - 3"
  • Optical Flats 4 - 6"
  • Optical Flats 7 - 9"
  • Optical Flats 10 - 12"
  • Optical Flats - over 12"
  • Precision Balls
  • Gear Wires (2 pc set)
  • Thread Wires (3 pc set)

Precision Tools / Hand Tools

  • Caliper to 6"
  • Caliper 7 - 12"
  • Caliper 13 - 24"
  • Caliper 25 - 36"
  • Caliper 37 - 48"
  • Caliper 49 - 60"
  • Caliper 61 - 72"
  • Caliper 73 - 120"
  • Bore Gage - Dial
  • Dial Indicator to 1"
  • Dial Indicator to 2"
  • Dial Indicator to 3"
  • Dial Indicator to 4"
  • Dial Indicator to 5"
  • Dial Indicator to 6"
  • Dial Mikrokator
  • Intrimic
  • Micrometer - Depth to 4"
  • Micrometer - Depth to 6"
  • Micrometer - Depth to 9"
  • Micrometer - Depth to 12"
  • Chamfer Gage
  • Micrometer - Inside to 6"
  • Micrometer - Inside to 12"
  • Micrometer - Inside to 24"
  • Micrometer - Inside to 36"
  • Micrometer - Inside to 48"
  • Micrometer - Inside to 60"
  • Micrometer - Inside to 72"
  • Micrometer - Inside to 84"
  • Micrometer - Inside to 96"
  • Micrometer - Inside to 120"
  • Adjustable Micrometer 0 - 4"
  • Adjustable Micrometer 7 - 12"
  • Adjustable Micrometer 13 - 24"
  • Adjustable Micrometer 25 - 30"
  • Adjustable Micrometer 31 - 40"
  • Adjustable Micrometer 41 - 60"
  • Micrometer - Outside 0 - 6"
  • Micrometer - Outside 7 - 12"
  • Micrometer - Outside 13 -24"
  • Micrometer - Outside 25 - 36"
  • Protractor - Digital
  • Protractor - Mechanical
  • Radius Gages (per leaf) w/o Readings
  • Radius Gages (per leaf) w/ Readings
  • Screw Pitch Gage (per leaf)
  • Employee Tool Box

Shop Equipment

  • Coordinate Measuring Machine 30"
  • Coordinate Measuring Machine 36"
  • Coordinate Measuring Machine 48"
  • Coordinate Measuring Machine 60"
  • Coordinate Measuring Machine 72"
  • Coordinate Measuring Machine 96"
  • Coordinate Measuring Machine 108"
  • Coordinate Measuring Machine 120"
  • Universal Length Measuring Machine
  • Electronic Amplifier
  • Height Gage - Digital to 12"
  • Height Gage - Digital to 18"
  • Height Gage - Digital to 24"
  • Height Gage - Digital to 36"
  • Height Gage - Digital to 48"
  • Height Gage - Digital to 60"
  • Height Gage - Vernier to 18"
  • Height Gage - Vernier to 24"
  • Height Gage - Vernier to 48"
  • Height Gage - Vernier to 72"
  • Height Master (per Step)
  • Riser Block
  • Optical Comparator to 15"
  • Optical Comparator to 36"
  • Hardness Tester - Brinell
  • Hardness Tester - Rockwell
  • Hardness Tester Combination
  • Hardness Test Blocks
  • Durometer
  • Supermic to 5"
  • Supermic 6 - 10"
  • Supermic 11 - 24"
  • Surface Plate - Minimum Charge
  • Surface Plate - per Square Foot
  • Surface Finish Machine
  • Surface Finish Standard

Squares/Levels / Angle Plates

  • 1-2-3 Block
  • Angle Plate to 8"
  • Angle Plate 9 - 12"
  • Angle Plate 13 - 18"
  • Cylindrical Square
  • Level - Machine
  • Level - Master
  • Level - Electronic
  • Parallel to 12"
  • Parallel 13 - 24"
  • Parallel 25 - 48"
  • Parallel 49 - 60"
  • Parallel 61 - 120"
  • Sine Bar to 12"
  • Sine Bar 13 - 20"
  • Sine Plate - Compound
  • Square to 12"
  • Square 13 - 24"
  • Straight Edge to 24"
  • Straight Edge 25 - 60"
  • Straight Edge 61 - 120"
  • V-Block

Thread & Cylindrical Ring Gages

  • Acme Thread Ring 0 - 2"
  • Acme Thread Ring 2 - 4"
  • Acme Thread Ring 4 - 6"
  • BSPT/BSP Thread Ring 0 - 2"
  • BSPT/BSP Thread Ring 2 - 4"
  • BSPT/BSP Thread Ring 4 - 6"
  • Buttress Thread Ring 0 - 2"
  • Buttress Thread Ring 2 - 4"
  • Buttress Thread Ring 4 - 6"
  • Cylindrical (Plain) Ring Gage .040 - 2.000"
  • Cylindrical (Plain) Ring Gage 2.001 - 5.500"
  • Cylindrical (Plain) Ring Gage 5.501 - 11.000"
  • Cylindrical (Plain) Ring Gage - Above 11.000"
  • Spline Ring Gage
  • Thread Ring Gage 0 - 1"
  • Thread Ring Gage 1 - 2"
  • Thread Ring Gage 2 - 4"
  • Thread Ring Gage 4 - 6"
  • For Non-Standard Pitch Diameter Add
  • Thread Ring Gage Above 6"
  • Thread Snap Gage 0 - 2"
  • Thread Snap Gage 2 - 6"
  • Thread Snap Gage - Non-Standard
  • NPSM Thread Ring 0 - 2"
  • NPSM Thread Ring 2 - 4"
  • NPSM Thread Ring 4 - 6"
  • NPT - NPTF - ANPT Thread Ring 0 - 2"
  • NPT - NPTF - ANPT Thread Ring 2 - 6"
  • NPT - NPTF - ANPT 6-Step Ring 0 - 2"
  • NPT - NPTF - ANPT 6-Step Ring 2 - 6"
  • Metric Thread Ring 1 - 25 mm
  • Metric Thread Ring 25 - 51mm
  • Metric Thread Ring 51 - 102mm
  • Metric Thread Ring 102 - 152mm
  • Luer Taper Rings
  • Taper Rings

Thread & Cylindrical Plug Gages

  • Air Probes - All
  • Acme Thread Plug 0 - 2" (per End)
  • Acme Thread Plug 2 - 4" (per End)
  • Acme Thread Plug 4 - 6" (per End)
  • BSPT/BSPP Thread Plug 0 - 2" (per End)
  • BSPT/BSPP Thread Plug 2 - 6" (per End)
  • Buttress Thread Plug 0 - 2" (per End)
  • Buttress Thread Plug 2 - 4" (per End)
  • Buttress Thread Plug 4 - 6" (per End)
  • Buttress Set Plug 0 - 4" (per End)
  • Buttress Set Plug 4 - 12" (per End)
  • For Non-Standard Pitch Diameter Add
  • Pin Gages (Class ZZ)
  • Plain Plug Gages 0 - 2" (per End)
  • Plain Plug Gages 2 - 6" (per End)
  • Plain Plug Gages 6 - 12" (per End)
  • Spline Plug Gage (per End)
  • Thread Plug 0 - 1" (per End)
  • Thread Plug 1 - 2" (per End)
  • Thread Plug 2 - 3" (per End)
  • Thread Plug 3 - 4" (per End)
  • Thread Plug 4 - 6" (per End)
  • Thread Plug 6 - 12" (per End)
  • Thread Set Plug 0 - 4" (per End)
  • Thread Set Plug 4 - 12" (per End)
  • NPSM Thread Plug 0 - 2" (per End)
  • NPSM Thread Plug 2 - 4" (per End)
  • NPSM Thread Plug 4 - 6" (per End)
  • NPT - NPTF - ANPT Plug 0 - 2" (per End)
  • NPT - NPTF - ANPT Plug 2 - 6" (per End)
  • NPT - NPTF - ANPT 6-Step Plug 0 - 2" (per End)
  • NPT - NPTF - ANPT 6-Step Plug 2 - 6" (per End)
  • Metric Thread Plug 0 - 25mm (per End)
  • Metric Thread Plug 25 - 51mm (per End)
  • Metric Thread Plug 51 - 102mm (per End)
  • Metric Thread Plug 102 - 152mm (per End)
  • Metric Set Plug 0 - 102mm (per End)
  • Metric Set Plug 102 - 305mm (per End)
  • Luer Taper Plugs
  • Taper Plugs
  • Weights - Avdp Class 6 & F
  • Weights - Gram Class 3 thru F

Torque / Force / Weights

  • Cable Tensiometer w/Card
  • Cable Tensiometer - New Card
  • Force Gage to 250 lbs
  • Force Gage above 250 lbs
  • Gram Gage
  • Torque Wrench to 250 ft/lbs
  • Torque Wrench Above 250 ft/lbs
  • Torque Watch
  • Torque Tester
  • Torque Transducer

Miscellaneous

  • Crimping Tool
  • Film Thickness Gage
  • Digital Film Thickness
  • Feeler Gage (per Blade)
  • Readings for Rule 6 - 72" (per Reading) Add
  • Rule 6 - 36" w/o Readings
  • Rule 37 - 72" w/o Readings
  • Tape Measure to 25 ft
  • Tape Measure to 50 ft
  • Tape Measure to 100 ft
  • Machine Inspection - Laser (per Hour)

Ship To:

Ledford Gage Lab, Inc.
227 Industrial Drive
Mulvane, Kansas 67110
Phone: 316/777-9300
Fax: 316/777-2220
www.ledfordgage.com

BSI CertificationAMTMA LogoA2LA Accredited  ©2016 Ledford Gage Lab Inc.